Header banner
Revain logoHome Page
🔋 high-strength petg filament by polymaker, 1.75mm logo

🔋 High-Strength PETG Filament by Polymaker, 1.75mm Review

3

·

Average

Revainrating 3 out of 5  
Rating 
3.0
🖨️ 3D Printing Supplies, 🏭 Additive Manufacturing Products

View on AmazonView on ЯM

Media

(4)
img 1 attached to 🔋 High-Strength PETG Filament by Polymaker, 1.75mm
img 2 attached to 🔋 High-Strength PETG Filament by Polymaker, 1.75mm
img 3 attached to 🔋 High-Strength PETG Filament by Polymaker, 1.75mm
img 4 attached to 🔋 High-Strength PETG Filament by Polymaker, 1.75mm

Description of 🔋 High-Strength PETG Filament by Polymaker, 1.75mm

😀 【Almost Unbreakable!】 - PolyMax PETG is an engineered PETG with enhanced toughness, ductility and durability. This 3D filament 1.75 is the perfect material for applications demanding high impact resistance. The mechanical properties can be compared to ABS. PolyMax PETG combines excellent mechanical properties with great printability. Selected color: White PETG filament 1.75mm ( PETG White Filament ). 🧵 【Tangle Free & Moisture Free】 - PolyMax PETG is carefully winded to avoid any tangling issues, dried and vacuum sealed in a resealable ziplock bag with desiccant. Please make sure to NEVER let go the tip of the filament as it may create nodes. Holes on the side of the spool can be used to prevent this issue. 🛠️ 【Excellent Toughness & Layer Adhesion 】 - No warping, no jamming, no blobs or layer delamination issues. PolyMax PETG is a worry-free 3D Printer Filament White which has great bed adhesion, very consistent color and dimensional accuracy. It is one of the toughest compare to all competitive filaments such as PLA+ filament 1.75mm. (Reduce or off the fan speed for even stronger prints). 🎁 【Best Gift for your 3D Printer】 - PolyMax PETG is a high quality 1.75 filament PETG and your 3D Printer will love it. Polymaker White PETG 1.75mm filament is the ideal gift for you and your 3D Printer. ⚙ 【Printing Settings】 - Nozzle: 235 ̊C; Bed: 80 ̊C; Speed: 60mm/s (Settings can be adjusted depending on the color and type of filament you have selected). ⚠️ 【Important Note】 - Please make sure to double check the diameter of your order as it may automatically change when selecting a color. Selected diameter: PolyMax PETG filament 1.75mm White ( PETG filament White ). 🛡️ 【Risk Free & Lifetime Technical Support】 - We offer a full refund if the product is not performing as expected. This PETG is designed for your toughest 3D Printer Prints. Let us help you get your perfect beatiful prints and contact us via Amazon anytime you need.

Reviews

Global ratings 3
  • 5
    0
  • 4
    2
  • 3
    0
  • 2
    0
  • 1
    1

Type of review

Revainrating 4 out of 5

lays down like butter

This gray Polymax PLA is one of the best PLAs I've ever used. I've tried Hatchbox, Sunlu, Tech Bear, Geetech and a few others and this definitely fits. I use and end 3 v2 at 207 degrees with a 55 degree bed. Retract set to 5mm at 45mm/s and 27mm/s with 0.2mm nozzle. The detail of my D&D miniatures is amazing. I love the quality of the resin. After you adjust your settings, it has a slight stretch, leaves minimal layer lines, and is slightly more flexible than PETG and feels more durable than…

Pros
  • 3D printing filament
Cons
  • wrinkled

Revainrating 1 out of 5

2 rolls good, 2 rolls bad

**Updated September 2021** Terrible and unreliable. The two replacement spools were just as bad as the two I returned. One managed to jam my printer so badly that it is now out of alignment (I got stuck on a bell while printing and 10 minutes was enough to damage my printer). I have no idea what's going on at Polymaker, but buyers beware. This filament is low quality and can damage the printer.**Previous Review**The first two rolls of black PLA were fantastic. Good adhesion, no buckling, clean…

Pros
  • Industrial & Scientific
Cons
  • Questionable senior purchase

Revainrating 4 out of 5

Glass-smooth layer lines are not possible, but some curvature occurs

Flows smoothly like water glass; sticks well to itself and adheres well to the bed. With a low layer height, e.g. B. 0.1 or less, you can get perfectly smooth prints with almost no visible layers. Very impressed with that. Suppose this is due to incredible quality control of width and material properties. I've also read that you can smooth out this material with acetone, but haven't tried it yet. I still have a serious problem with buckling up and getting out of bed. (See photo) Given the level

Pros
  • Consumables for 3D printing
Cons
  • No automatic