Tubing Cutter 1/8 To 1-3/8 Inch For Pipe Copper PVC Thin Stainless Steel Tube With Extra Blade And Reamer Review

bought this to cut a mountain bike steerer tube , I upgraded my front fork to a new air fork and I needed something to trim off the excess length , this tool struggled with a 1/8 in thick aluminum 1/18 diameter tube and after 20 minutes it finally cut the tube . Then Tried to cut a steel bike seat post down to size , it took 30 minutes to cut that and distressed the tube so bad it is junk ! My 1st clue should have been when the packaging said " for refrigerant tubing "thank God I had a spare…

The reviews that say it doesn't stay on track are right. You have to really dig in and monitor to make sure you're cutting through.That said, it did the job and for not a lot of money. I needed to cut down some metal closet rods, and it worked. I'm happy I didn't get a $100 one because I'm not a professional. I don't use it enough to merit getting one that will last for years. I'm glad I got this one, even though I had to be more vigilant about the blade moving off course.

This works fine but feels a little flimsy. The deburring cutter is also a little small for 1/2 I’d tubing. But it works and is low priced.

Note: I’ve never used one of these before. Works well for cutting mountain bike handlebars. I slightly tightened the cutter on the bar, then used a ruler to find the amount of bar I wanted to cut by measuring to the edge of the blade. Then I tightened the cutter down, after a pass or two checked the cut to make sure it was cutting the right length, then tightened a half turn every time it loosened up until it had cut all the way through the bar. Easy peasy. I also like how small the cutter is…

I was expecting a cheap tube cutter. Actually it cuts better than any other tube cutter I've owned. Excellent value! The tool may produce a lot of debris or metal shavings during use!

I used this on a few custom lightsaber blades and for that job, its excellent. I even used it to cut a Master Replicas force FX blade in half before I threw it out from damage as their basically good for show, not so much for go. I've made a few decorative blade plugs with it too. This is a great little tool to have for anyone who dabbles in the lightsaber scene!

Used this to cut my wife's new handle bars down and it worked flawlessly. As far as long term. Do not know yet. It was purchased just to cut bars down as we upgrade them.

I had to purchase a different pipe cutter. This was larger and more awkward than most leading to botched pipe cuts. I bought a smaller cutter at Lowe's and it was much more effective. This might be ok if you have ample space surrounding your plumbing.

It has a tendency to smash thinner pipes like the supply lines for a water heater. And I tried to use it on half inch copper and it walked.

I purchased this tube cutter because I make a lot of my own tools, which happen to have brass ferrules. The cutting wheel itself is aggressively chattered, to the point where the variance of the cutting wheel may actually lose grip on the tube. I guess it's an okay tool for someone who doesn't care about ease of use or craftsmanship, but I wouldn't purchase again.

Cut through steel golf club shafts like butter. Great low-cost tool for the job, low cost, quick, easy to use. The tool may strip or deform the tubing while cutting.

Work perfectly as described. I was worried that it may not be able to cut my bicycle's seat post tube. But it just worked and very easy to use. Just put the seat post tube in and spin and tighten up the knob. For around 2 mins, it cut the tube flawlessly.

As other reviewers have mentioned this does not cut straight at all! Unless you are trying to tread your pipe stay away, will be returning.

I needed to cut some small diameter stainless steel tubing. It really is easy to use and cuts well. I had some 6 mm OD (0.246") tubing with a 1 mm ( 0.039") wall thickness and it had no issues cutting this.

I tried to cut a stainless steel tube, OD 8 mm, wall thickness 1 mm. I ruined the blade during my first cut! Good that it came with a replacement blade.

It’s simple to use and cuts pipe quickly. What more can I say? I bought this pipe cutting tool to cut my 1/4” and 3/8” copper line set. The replacement blade and reamer are helpful. Worth mentioning is that the cutter keeps a firm grip on the tube to prevent deformation during the cut. Good stuff

This cutter actually does a great job cutting pipe. It seems to damage the pipe more than my other cutter, but it is easier to use. I would strongly recommend keeping a good file handy to clean up the pipe after it's cut. If it could avoid doing this, it would easily be a 5 star product.

Seriously so easy to use! Used to cut Cooper pipe for our wedding arch. I WAS SHOCKED at how easily this worked It worked for me for the limited cuts I needed..

This tube cutter works good. Have used it to cut aluminum and steel pipe several times without issue. Good cut, minimum distortion and deflection. Quick and clean, consistent.

Used it to cut the handlebars of my mtb and it cuts the aluminum very easy and a clean clean cut. Very nice tool Thanks for attention.