Relay Aqara SSM-U02 5 A Review

I do not recommend loading more than 1000 watts. I know cases that when overloaded, the relay fails quickly. In general, the best option for light, but not for an outlet.

The connection took a few minutes, anyone who is more or less versed in electricity will connect without problems. Connected to the station, it works clearly and with minimal delay.

Aqara native hub is required, or we are waiting for support from . Requires a deep socket, or a small switch mechanism to fit everything. Now it's idle :( Pros: Made very high quality. Works with two 6w Gauss Filament LED bulbs. Got cons: It did not connect directly to Station 2 via ZigBee. The device is detected, but cannot connect :( It does not fit into the socket with the Unica switch, 2mm is not enough in depth.

Apparently the quality leaves much to be desired, and the representative office of the company exists only for sale, and not for solving problems. Pros below: Easily integrates into a smart home, simply connects and configures. Zigbee Cons below: One of the 2 came defective (did not turn on when connected to the network). Installed far from immediately, it took more than 2 weeks. Wrote in support of akara, twice. Both times just ignored.

I recommend! Some pros: I really liked this relay. Pretty easy to install, everything went according to clear instructions. Works great with voice assistants. Cons: For 2 weeks of use, I did not find any shortcomings, I am completely satisfied with the purchase.

Unfortunately it turned out to be wrong. I connected everything according to the scheme: L phase, L1 to the lamp, S0 and S1 to the switch.

Has some pros: There are no questions about the relay, it’s small, it fit into the socket, but . Cons below: It does not connect to station 2. We look forward to when this opportunity is given.

In general, a very convenient relay. But the question is still not clear to me. Aqara is one of the subsidiaries of Xiaomi. They produce products for 2022, but do not add their mi home 2022 devices (this also applies to E1 / H1 switches for the 2022 socket). That is, if you need both switches / relays and equipment, then all this to match is such a hemorrhoids. And if you don’t have an Android home yet, then you can safely take 2 gateways. One separately for switches and relays for the acar…

If the budget is unimportant feel free to take. If important - pay attention to tuya. The relay of this company has its own small drawbacks, but the cost is three times lower

Some pros: Works stably, does not need a neutral wire, fits in a box behind the switch, although with difficulty. Its cons: Unable to connect with the old Aqara center, had to buy a new one with ZigBee 3.

It is very convenient that it does not require pulling to zero and can be used with the most common switch. I was surprised by the size, it fits in an ordinary socket, the antenna quietly hides under the body of the switches. PS. Now I learned about protection against overheating, for the first time I hear about this, we will use it))

Once again I am convinced that Station 2 in terms of a smart home is unnecessary junk. technical support does not understand how their equipment works at all .

Bought for light control. A 45mm Schneider socket is included in the side dimensions, a Schneider Unika switch is placed on top, but only if there are no wires inside the socket and in the switch (none). Otherwise, it does not fit a couple of millimeters. He pulled it out of the case, pulled it into heat shrink, immediately -5mm of height is won. It does not connect to the akara hub of the 1st version (Chinese server region), the hub says that the device is connected, but it is not in the list.

I bought a product to automate the on / off of the contour lighting at home. He coped with the task, but there are some nuances: 1) According to the instructions, it should be fixed on the back wall of the socket, but the problem is that in China the sockets are square, while ours are round, because of this it is not possible to attach either it or the antenna (which should also be glued to the top wall of the socket ). 2) My socket was not deep enough, so I had to abandon the idea of…

Different pros: Makes any switch smart, especially convenient to use with switches in a common frame where you can’t put a ready-made smart switch Its cons: We are waiting and hoping that the next versions will be smaller. Not the most convenient installation process in the socket at the current dimensions.