Sawing machine Makita 2704N, 1650 W Review

Great machine, I'm buying a second one. I recommend to buy. True, the price for it now does not correspond to its functionality and is really overpriced relative to consumer qualities.

Ownership experience 7 years. Convenient sliding table in two directions. not turned off sometimes for 5-6 hours. Of the breakdowns, only the replacement of brushes. Storage in a humid room, after breaks in work, it was necessary to remove the bottom cover and lubricate the guides for raising and lowering the saw (rusted). I changed the gear on the tilt shaft of the saw, but it’s more likely from the of the tool, I didn’t always work with a vacuum cleaner and right on the ground (the inner…

I have owned the machine for 2 years. Dissatisfied with the results of the operation. Immediately after the purchase, I had to give the machine for adjustment - there was no parallelism of the disk relative to the guides and the parallel stop was constantly knocked off when sawing, as it was sawing into a "wedge". After the servicemen (SP Korolev S. S. in Hong Kong) lasted 2 months, they gave it away without setting it up. In conclusion, they wrote "the manufacturer did not provide for the…

But in the end I had to fake it, because. there is a defect in the casting of the casing, therefore, the front and rear parts of the disk differ by 4 mm relative to the parallel stop, so I had to put a 4 mm insert under the rear upper stop of the engine. After the alterations, it became very convenient in pruning, dissolution and sawing! Pros: 1. Quick adjustment, both in height and angle, as well as in the rip fence. 2. Good removal of sawdust. 3. Good native drive. Some cons: 1. Got which…

The disk is sharp. The board is 50 mm. On the 3rd board L 3000 mm 50 × 150 with a feed rate of 1 meter per hour 😠 this narrow-eyed miracle started to smoke again. level I have 25 years) It was stored, serviced, lubricated, after each work it was blown by the compressor. As a result, the appearance is beautiful, but the engine💩. I have no complaints about the rest of Makita. frames for pictures, pegs for tomatoes and cucumbers, etc. I hope the review was useful.

I won’t say that I use it in the tail and mane, but I use it. This year, I took it apart for the first time and completely cleaned and lubricated everything. It turned out to be an extremely simple operation! Well, if you don't rush. Two hours - elementary! This is if it's the first time. In the second, I think I can handle it in half an hour. The main task in the last year is the LONGITUDINAL sawing of oak boards. More than 5 cm is already difficult, plus it also "drags" the boards with an…

I would not have bought this saw if I was guided by the reviews about it here on the market. Fortunately, the workshop has a discussion of its 100 pages, 700 posts. A lot of opinions, and most importantly - a lot of simple and effective tips and solutions for setting up and operating (thanks to all the craftsmen). Spend 1 day adjusting your saw, making different fixtures, and get amazing accuracy. Smiling reviews like: "we choked her, choked her (cubic meters) and she burned down, so she's…

Disappointed in the makite, already the second tool (the first - a small grinder) fails the engine, burns in general. I will switch to the Germans. I owned a circular saw for the second year, in the first I made several bars of 50mm, this year two bars of 50x30 and in the third, a skiff to the engine, smoked. I've never heard of Bosch. It's a shame that for such money you buy low-quality equipment.

Great machine for small carpentry and joinery work. It requires adjustments, care and understanding - why do you need it - there are other machines for making fences. It has been in operation for 9 years. Some pros: The workmanship of most machine components is at a height, the ability to adjust almost everything and everything, sawing accuracy, power when working with most wood species. Height of departure of a saw. The small sizes. With its cons: Not very durable plastic case, unsuccessful…

A fairly convenient device for carpentry, summer cottage and general work, after the purchase it replaced the miter saw, on the machine you can do everything conveniently. Practically unsuitable for carpentry work, it needs refinement and adjustment after purchase (my copy): the kerf width ruler gave a constant error of the order of a millimeter. In principle, the kerf stop can walk along the far end of the fixture; without experience, it is difficult to set the angle of the disk, since the…

Different pros: Sawing fun and good but not for long You can connect a vacuum cleaner) Has some cons: The engine overheats, there is no protection against overheating, they sent it in for repair. Saw size mounts are not very reliable