💡 Podoy GS-100A Flash Strobe Controller: Enhance LED Brake Tail Stop Light Performance! Review

Before applying any of these, make sure the label has not been misapplied at the factory. The product I received had the label set to 180 degrees and marked the input wires as an output. The telltale sign is if the red and black wires on the ends don't match the top and bottom orientations, they should match the diagram on the label.

Installed it first while rewiring the lights. So I've already taken everything apart. In any case, it is very easy to install. The input is the wire that goes to the bike's headlights, specifically the brake light, not the running lights. The output is a wire from the controller to the light. Works very well and the product seems to be quite durable. True, the product is very simple in terms of electronics. It works and can be installed with very basic knowledge.

I have an old Honda motorcycle (1988). I wanted to improve the visibility of the brake light so I bought it. It's compact, well made and cheap. It was easy to install but I wanted to be able to remove it and restore the bike to its original condition. So I had to buy some non-standard connectors. Then I noticed that this block is only for LED bulbs. So I had to replace the LED brake light bulbs (red). WOW. It works well and the brake light is much more noticeable. A good buy.

I installed this to work with my factory 3rd brake light which is in the spoiler and LED. Watch the spoiler in the attached video to see the blinking pattern. Voltage skills are very easy to establish. If you don't understand electricity, don't give a product a bad review based on your ignorance. If you connect it backwards, the LEDs will still light up, but no flash. It works great, is very cheap and easy to install. What more could you want from a cool little setup? Because of the cheap price

This is definitely my flasher module. I've installed this in the rear of every bike I've owned with additional LED strips underneath. There are loads of videos out there so I'll spare you mine which is nothing special but I swear by the GS100A blinker as the most perfect. A fast flash starting before a slower and harder one is great on bikes especially because you can just use fast pumps to get a constant flash to get the attention of almost everyone behind you and I'm VERY paranoid, when I get

I've just bought a third replacement LED stop light and decided to toss this indicator with it in my shopping cart. I've seen other drivers on the road using this mod and it always caught my attention when the traffic slowed down. Every time I see it I think it's a great idea. Now I want it for my truck. My 2002 Ford Ranger pickup has a third brake with a built in charge light so the installation wasn't very easy. Both the truck light and brake light have separate ground and power wires, so you

Edited my original review. Put it on my bike in May 2019. Connectors are soldered and shrink wrapped. Has worked great for 3500 km. September 2019 motorcycle sold. He took everything that wasn't b4 from him when he sold it. And here I am with wire cutters and soldering iron in my hands. Thought let's hook it up to my third brake light on my focus. A bad idea worked when I tested it, but that night while I was driving it kept flashing and weird when I pressed the brake pedal. I've had it on my…

I don't know why this blinker has mixed reviews - it works perfectly (and has worked for several months). I tried to figure out which wire was under the dash and found that it was small enough that I could just thread it over the headliner and leave it there. I also replaced incandescent bulbs with LEDs at the same time to give them a stronger strobe effect and it works great. After a few months of use, I noticed that people in traffic are surprised by my bumper and quickly notice it. when i…

I've noticed this with other cars and wanted to be noticed too. This LED strobe controller is easy to install with minimal electrical knowledge. I wanted to install it in such a way that it can be easily switched back to the default version if any authorities object. I used the male and female connectors to beef up the controller with the two wires going to the third LED brake light. I accessed the wires and made sure there were enough of them to be stripped, twisted and crimped with a…